Mô tả sản phẩm
Photoelectric sensors
Features
| Sensor/ detection principle | Photoelectric retro-reflective sensor, autocollimation |
| Dimensions (W x H x D) | 15.5 mm x 48.5 mm x 42 mm |
| Housing design (light emission) | Rectangular |
| Sensing range max. | 0 m … 4 m |
| Sensing range | 0 m … 4 m 1) |
| Type of light | Visible red light |
| Light source | PinPoint LED 2) |
| Light spot size (distance) | ? 25 mm (1.5 m) |
| Wave length | 660 nm |
| Adjustment | IO-Link, Single teach-in button 3) |
| Pin 2 configuration | External input, Teach-in input, Sender off input, Detection output, logic output, Device contamination alarm output |
| Diagnosis | Device contamination monitoring, Quality of teach-in |
| AutoAdapt | ? |
| Special applications | Detecting transparent objects |
- 1) Reflector PL80A.2) Average service life: 100,000 h at TU = +25 ?C.3) Mode I, 10 % attenuation.
Mechanics/electronics
| Supply voltage | 10 V DC … 30 V DC 1) |
| Ripple | ? 5 Vpp 2) |
| Power consumption | 30 mA 3) |
| Switching output | PNP |
| Switching mode | Light/dark switching |
| Signal voltage PNP HIGH/LOW | Approx. VS ? 2.5 V / 0 V |
| Output current Imax. | ? 100 mA |
| Response time Q/ on Pin 2 | 200 ?s … 300 ?s 4) 5) |
| Switching frequency | 1,500 Hz 6) |
| Switching frequency Q / to pin 2 | ? 1,500 Hz 7) |
| Attenuation along light beam | > 8 % |
| Connection type | Male connector M12, 4-pin |
| Circuit protection |
A 8) B 9) C 10) D 11) |
| Protection class | III |
| Weight | 120 g |
| Polarisation filter | ? |
| IO-Link | ? |
| Transmission rate | COM2 |
| Housing material | Metal, Zinc diecast |
| Optics material | Plastic, PMMA |
| Enclosure rating |
IP66 IP67 |
| Special feature | Detecting transparent objects |
| Ambient operating temperature | ?40 ?C … +60 ?C |
| Ambient storage temperature | ?40 ?C … +75 ?C |
| UL File No. | NRKH.E181493 & NRKH7.E181493 |
| Repeatability Q/ on Pin 2: | 100 ?s 5) |
- 1) Limit values when operated in short-circuit protected network: max. 8 A.2) May not exceed or fall below Uv tolerances.3) Without load.4) Signal transit time with resistive load.5) Valid for Q on Pin2, if configured with software.6) With light/dark ratio 1:1.7) With light / dark ratio 1:1, valid for Q on Pin2, if configured with software.8) A = VS connections reverse-polarity protected.9) B = inputs and output reverse-polarity protected.10) C = interference suppression.11) D = outputs overcurrent and short-circuit protected.
Classifications
| ECl@ss 5.0 | 27270902 |
| ECl@ss 5.1.4 | 27270902 |
| ECl@ss 6.0 | 27270902 |
| ECl@ss 6.2 | 27270902 |
| ECl@ss 7.0 | 27270902 |
| ECl@ss 8.0 | 27270902 |
| ECl@ss 8.1 | 27270902 |
| ECl@ss 9.0 | 27270902 |
| ETIM 5.0 | EC002717 |
| ETIM 6.0 | EC002717 |
| UNSPSC 16.0901 | 39121528 |
Smart Task
| Smart Task name | Base logics |
| Logic function |
Direct AND OR WINDOW Hysteresis |
| Timer function |
Deactivated On delay Off delay ON and OFF delay Impulse (one shot) |
| Inverter | Yes |
| Switching frequency |
SIO Direct: 1500 Hz 1) SIO Logic: 1500 Hz 2) IOL: 1100 Hz 3) |
| Response time |
SIO Direct: 200 ?s … 300 ?s 1) SIO Logic: 400 ?s … 500 ?s 2) IOL: 400 ?s … 750 ?s 3) |
| Repeatability |
SIO Direct: 100 ?s 1) SIO Logic: 100 ?s 2) IOL: 350 ?s 3) |
| Switching signal QL1 | Switching output |
| Switching signal QL2 | Switching output |
- 1) SIO Direct: sensor operation in standard I/O mode without IO-Link communication and without using internal sensor logic or time parameters (set to “direct”/”deactivated”).2) SIO Logic: Sensor operation in standard I/O mode without IO-Link communication. Sensor-internal logic or timing parameters plus Automation Functions used.3) IOL: Sensor operation with full IO-Link communication and usage of logic, timing and Automation Function parameters.
Communication interface
| Communication interface | IO-Link V1.1 |
| Communication Interface detail | COM2 (38,4 kBaud) |
| Cycle time | 2.3 ms |
| Process data length | 16 Bit |
| Process data structure |
Bit 0 = switching signal QL1 Bit 1 = switching signal QL2 Bit 2 … 15 = empty |
