Mô tả sản phẩm
Photoelectric sensors
Features
| Sensor/ detection principle | Through-beam photoelectric sensor |
| Dimensions (W x H x D) | 20 mm x 55.7 mm x 42 mm |
| Housing design (light emission) | Rectangular |
| Sensing range max. | 0 m … 45 m |
| Type of light | Visible red light |
| Light source | PinPoint LED 1) |
| Light spot size (distance) | ? 90 mm (8 m) |
| Wave length | 635 nm |
| Adjustment |
BluePilot: With alignment aid IO-Link |
| Pin 2 configuration | External input, Teach-in, switching signal |
- 1) Average service life: 100,000 h at TU = +25 ?C.
Mechanics/electronics
| Supply voltage | 10 V DC … 30 V DC 1) |
| Ripple | ? 5 Vpp |
| Power consumption, sender |
? 30 mA 2) < 50 mA 3) |
| Power consumption, receiver |
? 30 mA 2) < 50 mA 3) |
| Switching output |
PUSH/PULL PNP NPN |
| Output: QL1 / C | Switching output or IO-Link mode |
| Output function | Factory setting: Pin 2 (MF): NPN normally closed (light switching), PNP normally open (dark switching), Pin 4 (QL1/C): NPN normally open (dark switching), PNP normally closed (light switching), IO-Link |
| Switching mode | Light/dark switching |
| Signal voltage PNP HIGH/LOW | Approx. VS ? 2.5 V / 0 V |
| Signal voltage NPN HIGH/LOW | Approx. VS / < 2.5 V |
| Output current Imax. | ? 100 mA |
| Response time | ? 500 ?s 4) |
| Switching frequency | 1,000 Hz 5) |
| Connection type | Cable with M12 male connector, 4-pin, 270 mm 6) |
| Cable material | PVC |
| Circuit protection |
A 7) B 8) C 9) D 10) |
| Protection class | III |
| Weight | 140 g |
| IO-Link | ? |
| Housing material | Plastic, VISTAL? |
| Optics material | Plastic, PMMA |
| Enclosure rating |
IP66 IP67 |
| Test input sender off | Test at 0 V |
| Ambient operating temperature | ?40 ?C … +60 ?C |
| Ambient storage temperature | ?40 ?C … +75 ?C |
| MTTFd: mean time to dangerous failure | 539 years |
| UL File No. | NRKH.E181493 & NRKH7.E181493 |
- 1) Limit values.2) 16 V DC … 30 V DC, without load.3) 10 V DC … 16 V DC, without load.4) Signal transit time with resistive load in switching mode. Different values possible in COM2 mode.5) With light/dark ratio 1:1 in switching mode. Different values possible in IO-Link mode.6) Do not bend below 0 ?C.7) A = VS connections reverse-polarity protected.8) B = inputs and output reverse-polarity protected.9) C = interference suppression.10) D = outputs overcurrent and short-circuit protected.
Classifications
| ECl@ss 5.0 | 27270904 |
| ECl@ss 5.1.4 | 27270904 |
| ECl@ss 6.0 | 27270904 |
| ECl@ss 6.2 | 27270904 |
| ECl@ss 7.0 | 27270904 |
| ECl@ss 8.0 | 27270904 |
| ECl@ss 8.1 | 27270904 |
| ECl@ss 9.0 | 27270904 |
| ETIM 5.0 | EC002719 |
| ETIM 6.0 | EC002719 |
| UNSPSC 16.0901 | 39121528 |
Smart Task
| Smart Task name | Base logics |
| Logic function |
Direct AND OR Window Hysteresis |
| Timer function |
Deactivated On delay Off delay ON and OFF delay Impulse (one shot) |
| Inverter | Yes |
| Switching frequency |
SIO Direct: 1000 Hz 1) SIO Logic: 800 Hz 2) IOL: 650 Hz 3) |
| Response time |
SIO Direct: 500 ?s 1) SIO Logic: 600 ?s 2) IOL: 750 ?s 3) |
| Repeatability |
SIO Direct: 150 ?s 1) SIO Logic: 300 ?s 2) IOL: 400 ?s 3) |
| Switching signal QL1 | Switching output |
| Switching signal QL2 | Switching output |
- 1) SIO Direct: sensor operation in standard I/O mode without IO-Link communication and without using internal sensor logic or time parameters (set to “direct”/”deactivated”).2) SIO Logic: Sensor operation in standard I/O mode without IO-Link communication. Sensor-internal logic or timing parameters plus Automation Functions used.3) IOL: Sensor operation with full IO-Link communication and usage of logic, timing and Automation Function parameters.
Communication interface
| Communication interface | IO-Link V1.1 |
| Communication Interface detail | COM2 (38,4 kBaud) |
| Cycle time | 2.3 ms |
| Process data length | 16 Bit |
| Process data structure |
Bit 0 = switching signal QL1 Bit 1 = switching signal QL2 Bit 2 … 15 = empty |
| VendorID | 26 |
| DeviceID HEX | 0x800174 |
| DeviceID DEZ | 8388980 |
