Mô tả sản phẩm
Product portfolio
Performance
| Number of steps per revolution | 8,192 |
| Number of revolutions | 8,192 |
| Resolution | 13 bit x 13 bit x 8,192 (8,192) |
| Error limits G | 0.25? 1) |
| Repeatability standard deviation ?r | 0.1? 2) |
- 1) In accordance with DIN ISO 1319-1, position of the upper and lower error limit depends on the installation situation, specified value refers to a symmetrical position, i.e. deviation in upper and lower direction is the same.2) In accordance with DIN ISO 55350-13, 68.3% of the measured values are inside the specified area.
Interfaces
| Communication interface | DeviceNet? | ||||
| Data protocol | DeviceNet Specification Release 2.0 | ||||
| Address setting | 0 … 63, DIP switches or protocol | ||||
| Data transmission rate (baud rate) |
DIP switches or protocol, 125 kBaud 250 kBaud 500 kBaud |
||||
| Status information | Network status LED, 2-colours | ||||
| Bus termination | DIP switch 1) | ||||
| Initialization time | 1,250 ms 2) | ||||
| Position forming time | + 0.25 ms | ||||
|
|||||
- 1) Should only be connected in the final device.2) Valid positional data can be read once this time has elapsed.
Electrical data
| Connection type | Connection adapter for DeviceNet 1) |
| Supply voltage range | 10 V … 32 V |
| Reverse polarity protection | ? |
| MTTFd: mean time to dangerous failure | 150 years (EN ISO 13849-1) 2) |
- 1) Please order the bus adaptor seperately.2) This product is a standard product and does not constitute a safety component as defined in the Machinery Directive. Calculation based on nominal load of components, average ambient temperature 40?C, frequency of use 8760 h/a. All electronic failures are considered hazardous. For more information, see document no. 8015532.
Mechanical data
| Mechanical design | Blind hollow shaft |
| Shaft diameter | 6 mm, 8 mm, 10 mm, 12 mm, 14 mm, 15 mm x 1/4″, 3/8″, 1/2? 1) |
| Weight | 0.59 kg |
| Shaft material | Stainless steel |
| Flange material | Aluminum |
| Housing material | Aluminum die cast |
| Start up torque | 1.2 Ncm, with shaft seal |
| Operating torque | 0.8 Ncm, with shaft seal |
| Permissible shaft movement, axial static/dynamic | ? 0.5 mm, ? 0.2 mm |
| Permissible shaft movement, radial static/dynamic | ? 0.3 mm, ? 0.1 mm |
| Moment of inertia of the rotor | 55 gcm? |
| Bearing lifetime | 3.6 x 10^9 revolutions |
| Angular acceleration | ? 500,000 rad/s? |
| Operating speed | ? 3,000 min?? |
- 1) Collets for 6, 8, 10, 12, 14 mm and 1/4″, 3/8″ and 1/2″ as accessories, separate order item. For 15 mm shaft diameter collet is not needed.
Ambient data
| EMC | According to EN 61000-6-2 and EN 61000-6-3 |
| Enclosure rating |
IP67, with shaft seal (according to IEC 60529) IP43, without shaft seal, on encoder flange not sealed (according to IEC 60529) IP66, without shaft seal, on encoder flange sealed (according to IEC 60529) |
| Permissible relative humidity | 98 % |
| Operating temperature range | ?20 ?C … +85 ?C |
| Storage temperature range | ?40 ?C … +125 ?C, without package |
| Resistance to shocks | 100 g, 6 ms (according to EN 60068-2-27) |
| Resistance to vibration | 20 g, 10 Hz … 2,000 Hz (according to EN 60068-2-6) |
Classifications
| ECl@ss 5.0 | 27270502 |
| ECl@ss 5.1.4 | 27270502 |
| ECl@ss 6.0 | 27270590 |
| ECl@ss 6.2 | 27270590 |
| ECl@ss 7.0 | 27270502 |
| ECl@ss 8.0 | 27270502 |
| ECl@ss 8.1 | 27270502 |
| ECl@ss 9.0 | 27270502 |
| ETIM 5.0 | EC001486 |
| ETIM 6.0 | EC001486 |
| UNSPSC 16.0901 | 41112113 |
