Mô tả sản phẩm
Product portfolio
Performance
| Number of steps per revolution | 8,192 (max.) |
| Number of revolutions | 8,192 (max.) |
| Resolution | 13 bit x 13 bit x 8,192 (8,192) |
| Max. resolution (singleturn, multiturn) | Maximum permissible resolution: 25 bit (12 bit singleturn x 13 bit multiturn or 13 bit singleturn x 12 bit multiturn). |
| Error limits G | 0.25? 1) |
| Repeatability standard deviation ?r | 0.1? 2) |
- 1) In accordance with DIN ISO 1319-1, position of the upper and lower error limit depends on the installation situation, specified value refers to a symmetrical position, i.e. deviation in upper and lower direction is the same.2) In accordance with DIN ISO 55350-13, 68.3% of the measured values are inside the specified area.
Interfaces
| Communication interface | SSI | ||||||||||||
| Parameterising data |
Number of steps per revolution Number of revolutions Code type Electronic adjustment |
||||||||||||
| Initialization time | 1,050 ms 1) | ||||||||||||
| Position forming time | 0.15 ms | ||||||||||||
|
|||||||||||||
- 1) Valid positional data can be read once this time has elapsed.2) Minimum, LOW level (Clock +): 500 ns.
Electrical data
| Connection type | Cable, 12-wire, radial, 10 m |
| Supply voltage range | 10 V … 32 V |
| MTTFd: mean time to dangerous failure | 150 years (EN ISO 13849-1) 1) |
- 1) This product is a standard product and does not constitute a safety component as defined in the Machinery Directive. Calculation based on nominal load of components, average ambient temperature 40?C, frequency of use 8760 h/a. All electronic failures are considered hazardous. For more information, see document no. 8015532.
Mechanical data
| Mechanical design | Blind hollow shaft |
| Shaft diameter | 6 mm, 8 mm, 10 mm, 12 mm, 14 mm, 15 mm x 1/4″, 3/8″, 1/2? 1) |
| Weight | 0.4 kg |
| Shaft material | Stainless steel |
| Flange material | Aluminum |
| Housing material | Aluminum die cast |
| Start up torque | 1.2 Ncm, with shaft seal |
| Operating torque | 0.8 Ncm, with shaft seal |
| Permissible shaft movement, axial static/dynamic | ? 0.5 mm, ? 0.2 mm |
| Permissible shaft movement, radial static/dynamic | ? 0.3 mm, ? 0.1 mm |
| Permissible Load capacity of shaft |
300 N / radial 50 N / axial |
| Moment of inertia of the rotor | 55 gcm? |
| Bearing lifetime | 3.6 x 10^9 revolutions |
| Angular acceleration | ? 500,000 rad/s? |
| Operating speed | ? 3,000 min?? 2) |
- 1) Collets for 6, 8, 10, 12, 14 mm and 1/4″, 3/8″ and 1/2″ as accessories, separate order item. For 15 mm shaft diameter collet is not needed.2) Take into account self-heating of 3.3 K per 1,000 rpm when designing the operating temperature range.
Ambient data
| EMC | According to EN 61000-6-2 and EN 61000-6-3 |
| Enclosure rating |
IP67, with shaft seal (according to IEC 60529) 1) IP43, without shaft seal, on encoder flange not sealed (according to IEC 60529) 1) IP65, without shaft seal, on encoder flange sealed (according to IEC 60529) 1) |
| Permissible relative humidity | 98 % |
| Operating temperature range | ?20 ?C … +85 ?C |
| Storage temperature range | ?40 ?C … +100 ?C, without package |
| Resistance to shocks | 100 g, 6 ms (according to EN 60068-2-27) |
| Resistance to vibration | 20 g, 10 Hz … 2,000 Hz (according to EN 60068-2-6) |
- 1) With mating connector inserted.
Classifications
| ECl@ss 5.0 | 27270502 |
| ECl@ss 5.1.4 | 27270502 |
| ECl@ss 6.0 | 27270590 |
| ECl@ss 6.2 | 27270590 |
| ECl@ss 7.0 | 27270502 |
| ECl@ss 8.0 | 27270502 |
| ECl@ss 8.1 | 27270502 |
| ECl@ss 9.0 | 27270502 |
| ETIM 5.0 | EC001486 |
| ETIM 6.0 | EC001486 |
| UNSPSC 16.0901 | 41112113 |
